Contact Us Today ! |info@onexlimited.com

plastic industry

Home|plastic industry

plastic industry

Ⅰ. What problems should be paid attention to when producing PC products?

By |2020-05-30T01:44:11+00:00May 29th, 2020|For all, plastic industry|

This article will explain the issues about producing PC products in detail and it is divided into 2 parts. This is the Part One which includes the following 5 aspects: Raw material drying PC plastics, even touching a bit of water, the situation of bonds broken for hydrolysis, lower molecular

How to solve the burnt injection parts?

By |2020-05-27T02:15:06+00:00May 27th, 2020|For all, plastic industry|

For some reasons, injection molds often get burnt during the production. With different  causes of the burnt injection parts like machinery, mold or molding conditions, the solutions adopted are also different.  1.  Machinery for example: For the overheating of barrel due to abnormal conditions, the resin is decomposed at high temperature, and is injected into

How to deal with the sudden failure of the injection molding machine ? You must be clear and logical!

By |2020-05-25T07:53:09+00:00May 25th, 2020|For all, plastic industry|

After reading this post, you will know some common characteristics and failures of injection molding machines and how to deal with and avoid them. Content 1. The common characteristics of injection molding machines   2. Procedures for quick and effective fault analysis and elimination Step 1 Perform symptom analysis while keeping

Ⅱ.Do you know the 30 common problems and solutions in the injection molding process?

By |2020-05-25T03:36:55+00:00May 20th, 2020|For all, plastic industry|

Part Two ( 16-30 ) What is the injection pressure of injection molding machine? Injection pressure P( kg / cm2 ) = [ л / 4 × ( D12-D22 ) × P × 2 ] / ( л / 4 × d2 ) What is the plasticizing capacity of injection molding machine? Plasticizing capacity W ( g / sec ) =

Ⅰ.Do you know the 30 common problems and solutions in the injection molding process?

By |2020-05-25T03:36:57+00:00May 18th, 2020|For all, plastic industry|

PART ONE ( 1-15 ) The product runs off the edge (flash edge)when being turned on. The reason and solution of the product lacking glue after a period of production. When the machine starts to work, the melt glue in the material tube of the injection molding machine has a long heated time,

The pollution of hydraulic system of injection molding machine and relevent maintenance plan

By |2020-05-25T03:30:40+00:00May 15th, 2020|For all, plastic industry|

Do you know the pollution of hydrauli system of injection molding machine? How to deal with it? The decisive factors for the quality of the hydraulic system of injection molding machine: Rationality of the system design Performance of the system components Maintenance and solutions for the pollution of the system. The pollution

5 Main Problems for Nylon Cable Tie Manufacturing

By |2020-05-25T09:02:22+00:00April 23rd, 2020|For all, plastic industry|

There are several main problem in the cable tie manufacturing: short shot, flashing, bubbles, gets yellow, brittle, and we will tell you why: China is the main production area for cable tie, with up to 50% of cable tie are made in China and exported to all over the world. We started developing nylon

Mold temperature controller, water type or oil type?

By |2020-05-26T06:11:17+00:00April 23rd, 2020|For all, plastic industry|

Mold temperature controller is a small equipment which used for heating the connected mold to obtain the correct operating temperature in a minimal or specified time and maintain the set temperature by heating or cooling. There two types of mold temperature controller on the market, oil type and water type. Heat transfer medium of mold temperature

PA66 cost soaring, how do nylon cable tie manufacture respond?

By |2020-05-25T08:59:18+00:00April 22nd, 2020|For all, plastic industry|

In 2018, Several leading manufacturers of PA 66 suffered from force majeure, resulting in insufficient supply of PA66 raw materials, contradiction between supply and demand, and soaring prices. PAThe common manners are: 1. Replace imported PA66 with domestic PA66 2. Increase the proportion of recycled materials 3. Increase the proportion of PA6 4. Adoption recycling

How does the injection molding machine accurately and efficiently control the temperature of the barrel?

By |2020-05-25T02:57:08+00:00April 22nd, 2020|For all, plastic industry|

1.The temperature of injection molding machine barrel controlled by the microcomputer, select the appropriate algorithm to control the heating band outside the barrel of the injection machine. Ensure that the working temperature of each section of the barrel can be kept within the set range according to the technical requirements. For precise plastic injection

Top Sliding Bar

This Sliding Bar can be switched on or off in theme options, and can take any widget you throw at it or even fill it with your custom HTML Code. Its perfect for grabbing the attention of your viewers. Choose between 1, 2, 3 or 4 columns, set the background color, widget divider color, activate transparency, a top border or fully disable it on desktop and mobile.

Recent Tweets

Newsletter

Sign-up to get the latest news and update information. Don't worry, we won't send spam!

[contact-form-7 404 "Not Found"]